[1magine]

Has anyone been able to enter the Z-30 engineering screen? Just curious.

[Its Spade]

why???????

[Robert Crist]

That's as far as I can get. I try to get the token with eScreen Keygen but it never accepts it. Don't know why.

[1magine]

why???????

Hot spot restriction.
I will try one that comes in to the firm next week with a prior unlocked e-screen bar.

[1magine]

http://i.imgur.com/BFrFuaP.jpg

That's as far as I can get. I try to get the token with eScreen Keygen but it never accepts it. Don't know why.

Make sure you are in Development mode. Also must do it in like 10-15 seconds.

[Robert Crist]

Give me a sec and I'll try again. Rebooting after pushing unlocked Android stuff.

EDIT: Nope. No go, still won't do it, Dev mode enabled, typing it in under 10s.

[00stryder]

Make sure you are in Development mode. Also must do it in like 10-15 seconds.

I honestly don't even remember if I turn on dev mode on my Z10 when I attempt to enter the escreens page. It makes sense, but I don't think I knew that it was a requirement before.

I've found that it works best to have the keygen open on another device prior to typing "escreens://" into your Z10/Z30 browser, so that you can use the most updated runtime possible. Also, manually bring up the keyboard IN the new escreens window that pops up, and don't use capital letters when typing in your device pin into the keygen or the unlock code into your device.

Posted via CB10

[Robert Crist]

I honestly don't even remember if I turn on dev mode on my Z10 when I attempt to enter the escreens page. It makes sense, but I don't think I knew that it was a requirement before.

I've found that it works best to have the keygen open on another device prior to typing "escreens://" into your Z10/Z30 browser, so that you can use the most updated runtime possible. Also, manually bring up the keyboard IN the new escreens window that pops up, and don't use capital letters when typing in your device pin into the keygen or the unlock code into your device.

Posted via CB10

That's what I'm doing -- I have it open on my desktop browser, loading up escreens, jamming down the uptime and then typing in the PIN on my Z30, both with caps, without caps, dev mode on, dev mode off, nothing.

[00stryder]

That's not very reassuring... I guess we just have to see if anybody with a Z30 has got it working already.

Posted via CB10

[00stryder]

I've been in it. I wanted to turn off LTE because I'm on AT&T and I was concerned it is using extra battery. It does not have LTE turned on by the way.

I don't have a Z30 but thanks for chiming in. Would you mind outlining your process of accessing the screen to help the other users?

Posted via CB10

[Robert Crist]

Open your browser and open escreen://
Open this site on another tab or on another device: eScreen Keygen
Enter the information: PIN, OS Ver (app ver) and Uptime EXACTLY as it is shown on escreen into the keygen form
2 finger swipe up from the bottom to open the keyboard
Type the code in all lower case. If you did everything right, the escreen should open.

The usual warning applies. You can brick your phone messing about in here. Don't blame me if you end up buying a new phone because you killed yours.

That's super odd, that's exactly what I did and that's what I'm still doing, and I can't get past the initial info screen...

EDIT: And low and behold, I take my sweet Jesus time typing in the key and it pops up with the full escreen...

[00stryder]

Lol I think your phone was just trying to embarrass you in front of your forum friends...

Posted via CB10

[mopar_fxr]

were you able to get through it and toggle your LTE?

[lawrencetungsten]

Hi, is there a possibility for the setting to be permanent after setting on escreen?

[ymb]

Hi, is there a possibility for the setting to be permanent after setting on escreen?

No
And regarding the op yes I opened it on my z30 on first try though on my q10 I still can't get it to open is there a different way to do it on the q10? I've done it already on two z30 and both worked the first time and q10 I tried 5 times and it didn't go


Z30STA100-3/10.2.1.3289

[lawrencetungsten]

Sorry, i don't have a Q10 to try out.
Thanks for your comment on z30

[olllllo1978]

I use the ES X app to generate the code and I haven't had a problem getting into my Escreen. I use it a lot to turn off LTE on my VZW Z30 when I'm in the field to save battery.

Posted via CB10